Capello Alarm Clock How To Set Time
User Guide Clock Radio with Bluetooth Speaker CR60 IMPORTANT Condom NOTIFICATIONS Circumspection: TO REDUCE THE RISK OF Electric Shock, Practise Non REMOVE COVER (OR Back). NO USER-SERVICEABLE PARTS Inside. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Dangerous VOLTAGE: The lightning wink with arrowhead symbol, inside an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to found a risk of electrical shock to persons. Attention: The exclamation point inside an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: Changes or modifications to this unit non expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Attention: Pour ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS Large DE LA FICHE DANS LA BORNE CORRESPONDANTE ATTENTION:P DE LA PRISES ET POUSSER JUSQU'AU Addicted. FCC RF Radiations Exposure Statement Caution: To maintain compliance with the FCC's RF exposure guidelines, place the product at least 20cm from nearby persons. The device must not be co-located or operating in conjunction with whatever other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may crusade harmful interference to radio communications. Still, there is no guarantee that interference volition not occur in a item installation. If this equipment does cause harmful interference to radio or television reception, which can exist adamant by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for aid. Compliance data: This device complies with Office 15 of the FCC Rules. Operation is subject to the following ii conditions: (1) this device may not cause harmful interference, and (ii) this device must accept whatsoever interference received, including interference that may cause undesired operation. WARNING: TO PREVENT FIRE OR Shock HAZARD, DO NOT Expose THIS Unit of measurement TO Rain OR Wet. SURGE PROTECTORS: Information technology is recommended to use a surge protector for AC connection. Lightning and power surges ARE Not covered under warranty for this product. WARNING: The batteries shall non be exposed to excessive rut such every bit sunshine, fire or the similar. WARNING: The mains plug is used every bit a disconnect device, the disconnect device shall remain readily operable. IMPORTANT SAFETY INSTRUCTIONS Some of the following information may not apply to your particular product; nevertheless, as with whatsoever electronic production, precautions should be observed during handling and use. 1. ii. 3. 4. 5. half dozen. 7. 8. nine. 10. eleven. 12. 13. 14. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus almost water. Make clean only with a dry cloth. Practice non block whatsoever of the ventilation openings. Install in accord with the manufacturer's instructions. Practise not install near any heat sources such as radiators, estrus registers, stoves, or other apparatus (including amplifiers) that produce rut. Do non defeat the safety purpose of the polarized or footing-type plug. A polarized plug has two blades with one wider than the other. A grounding blazon plug has 2 blades and a third grounding prong. The wide bract or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched specially at plugs, convenience receptacles, and the point where they exit from the appliance. But use attachments/accessories specified by the manufacturer. Apply just with the cart, stand, tripod, subclass, or tabular array specified by the manufacturer, or sold with the apparatus. When a cart is used, use circumspection when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of fourth dimension. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects accept fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Additional SAFETY PRECAUTIONS a. Do not expose this unit or the AC/DC adaptor to dripping or splashing h2o. Keep liquid-filled objects, such as vases, away from this unit and Air conditioning/Ac adaptor. b. To ensure that this unit is completely asunder, unplug it from the wall. c. Ensure that the Air conditioning/DC adaptor is hands accessible. d. Delight notation the information printed underneath the unit. e. Batteries should not be exposed to excessive estrus such as direct sunshine, fire, etc. f. Exercise not impede the ventilation of this unit of measurement by roofing the ventilation openings with items such as newspapers, table-cloths, curtains, etc. thousand. Keep open flames, such equally lighted candles, abroad from this unit. h. Practise non place this unit of measurement in closed bookcases, racks, or other spaces without proper ventilation. i. Use only the same or equivalent blazon batteries as there is a danger of explosion if the incorrect batteries are used or they are installed incorrectly. j. Dispose of batteries properly co-ordinate to environmental regulations. Inside the box CR60 Clock Radio with Bluetooth Speaker, Ac power adapter and user guide. AC power source Insert the minor end of the Air conditioning adaptor into the DC In Jack (located on the rear of the unit). Connect the other cease to a wall outlet providing 100-240V AC, 50/60Hz. The output of the provided Air conditioning/DC Adaptor is DC 5V ii.2A. Notes: Disconnect both ends of the ability cord when not in employ. supplied AC adaptor with the following spec.: Employ merely the Air conditioning In – 100-240V AC, 50/60Hz / DC Out – 5V 2.2A Backup battery To keep accurate fourth dimension, this unit uses (ii) "AAA batteries" (sold separately) for clock backup. These batteries keep the clock operating in the outcome of a power break. Backup bombardment installation 1. Open the battery door by pushing in on the tabs, and then removing the door. 2. Insert two (2) "AAA" batteries following the correct polarity indicated in the battery compartment. iii. Replace the battery door back on the compartment. Notes: The batteries are used to backup the clock and warning times when the AC adaptor is asunder or there is a power failure. Element of group i batteries are recommended for the longest backup time. When replacing the battery, do not disconnect the Ac power adapter otherwise the current time, warning, and station presets will exist erased. When to replace the battery The battery indicator on the display will appear when at that place are no batteries or when the batteries are depression. bombardment precautions: Follow these precautions when using batteries in this device: ane. Warning – Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type. 2. Use but the size and type of batteries specified. 3 .Be sure to follow the right polarity when installing the batteries as indicated in the Bombardment Compartment. A reversed battery may cause damage to the device. 4. If the device is not to exist used for a long period of time, remove the batteries to prevent harm or injury from possible battery leakage. five. Do not endeavor to recharge a battery not intended to exist recharged - it can overheat and rupture (Follow battery manufacturer'southward directions.) 6. Do not mix different types of batteries together (eastward.g. Alkaline, Rechargeable and Carbon-zinc) or old batteries with fresh ones. Location of controls ane. SNOOZE / Effulgence 2. ALARM ane 3. Power ON / OFF 4. SOURCE five. Alarm ii six. DC IN JACK 7. FM ANTENNA WIRE 8. USB CHARGING PORT 9. PLAY / RADIO PRESET 10. VOLUME + 11. TUNE Upwardly / MIN 12. BLUETOOTH PAIR / TIME SET thirteen. VOLUME 14. TUNE Downwards / HOUR 15. LED DISPLAY 16. SPEAKER 17. BATTERY COMPARTMENT (bottom of unit) LED display indicators i. BLUETOOTH 2. FM RADIO three. ALARM 1 four. ALARM 2 five. LOW Battery vi. AM Setting the clock 1. Plug in the CR60 but leave the power "OFF". 2. Press and hold the BLUETOOTH PAIR / Fourth dimension SET button until the clock flashes in the display. iii. Press the Melody DOWN / HOUR button repeatedly to prepare the hour and press the TUNE Up / MIN button repeatedly to ready the minute. 4. Printing the BLUETOOTH PAIR / TIME Set button over again to store the new clock setting. Note: If you do not printing whatsoever button for nigh 10 seconds while setting the clock, the clock setting volition be canceled. Setting the alarm 1. In standby mode, slide the Alert 1 switch to the "Ready" position and the display volition begin flashing. ii. Press the TUNE DOWN / HOUR or TUNE Upwards / MIN button to set up the desired alarm time. iii. Next press the Book + or VOLUME – button to set the maximum alarm volume. four. Slide the ALARM ane switch to RADIO or BUZZ position to complete the process, the warning fourth dimension will disappear and the alarm indicator will low-cal up on the display. Notes: To deactivate the alarm, slide the Warning ane switch to the "OFF" position. Before setting the alarm, make sure that the clock fourth dimension is set correctly (see "Setting the clock"). To wake to the radio warning, first tune to the desired station and adjust the volume (see "Playing the radio"), To ready Warning 2, simply follow the aforementioned directions in a higher place but use the ALARM 2 switch. Silencing the alarm 1. When the ALARM 1 sounds, slide the ALARM 1 switch to the "OFF" position to silence the alarm. 2. To reactivate ALARM one the next time information technology is needed, slide the Warning 1 switch to the "RADIO" or "Buzz" position and the ALARM 1 indicator will light upward on the display, then check to make sure the alert time is correct. Annotation: To silence or reactivate ALARM ii, merely follow the aforementioned directions above but use the ALARM 2 switch. Snooze 1. When alarm sounds, pressing the SNOOZE / BRIGHTNESS button will temporarily silence the alarm. The alarm will sound once again later approximately 10 minutes. ii. To extend the snooze elapsing, repeatedly press the SNOOZE / BRIGHTNESS button to cycle through and select 1 of the snooze presets. Notes: Once the snooze function has been activated, press the SNOOZE / Effulgence push someday and the display will evidence the remaining fourth dimension. Repeatedly printing the SNOOZE / Effulgence button to adjust or modify the electric current snooze time setting. Setting the display brightness There are three levels of display brightness available (the default setting is loftier). Press the SNOOZE / Brightness push button to cycle through and select the desired setting. Annotation: Make sure that the unit is non in warning sound status. Irresolute the input source With the CR60 powered "ON", repeatedly press the SOURCE button to modify the input source to bike between FM Radio and Bluetooth. Playing the radio 1. With the CR60 plugged in and powered "ON", repeatedly printing the SOURCE push until FM Radio indicator lights up on the display. 2. Repeatedly press the TUNE Upward / MIN or Tune Downwards / 60 minutes button to manually adjust the tuning on the display until the desired station appears. 3. For auto tuning, press and concur the TUNE UP / MIN or TUNE Downward / Hr button until the display starts to browse, so release the push button. The tuner will search and stop on the next strongest station information technology finds. Echo this process until the desired station appears on the display. Notes: Fully extend the FM antenna wire to increase reception sensitivity. Proceed digital music players or mobile phones away from the FM antenna equally this may crusade interference. Do not place the FM antenna near the AC power adaptor as this may lead to reception interference. Setting radio presets i. To preset a radio station to memory, offset follow the steps above to tune in the desired station. 2. Press and hold the PLAY / RADIO PRESET push button to create a preset for the electric current station. "P" will appear and "##" (the preset number) will blink on the display. 3. Press the Tune UP / MIN or Tune DOWN / 60 minutes push button to select a preset number (01- 10). Press the PLAY / RADIO PRESET button once again to confirm the setting and the station will be saved into retentivity. 4. Repeat these steps for up to 10 presets, every bit desired. 5. To recall a preset station, repeatedly press the PLAY / RADIO PRESET button until the desired preset number appears in the display and the station tunes in. Note: Saving a new station preset in the aforementioned position as a previously saved station will supervene upon the previously stored station for that preset number. Bluetooth Functioning You tin can stream audio wirelessly to CR60 from up to 33' away using your iPhone, iPad, iPod, Android, laptop, or other A2DP Bluetooth enabled device. i. Press the POWER ON/OFF push to turn on CR60. two. And so press the SOURCE or BLUETOOTH PAIR / Fourth dimension Ready push. The Bluetooth LED indicator will flash on the brandish. 3. Plow on your A2DP Bluetooth device and enable Bluetooth. 4. Search for Bluetooth devices and select "CR60". 5. The Bluetooth LED indicator volition change from flashing to solid indicating that your Bluetooth device is connected to CR60. Notes: - Press and hold the BLUETOOTH PAIR / Time SET push button for three seconds to disconnect the Bluetooth connection. The unit of measurement will return to pairing way and the Bluetooth LED indicator on the display will flash. If asked for a countersign, enter "0000". Reconnecting your Bluetooth devices Once your Bluetooth device has been paired with CR60, it is simple to reconnect them. 1. Make sure that CR60 is powered on and within range. 2. Select "CR60" from the list on your Bluetooth device. 3. The Bluetooth LED indicator on the display will change from flashing to solid, indicating that your Bluetooth device is reconnected to CR60. Notes: For the all-time audio performance, turn the book on your Bluetooth source device all the fashion up. USB charging port The CR60 features one (1) USB port located on the rear of the unit (see "location of controls"). The USB port support powering and charging most devices including iPhones, iPads, iPods, E-readers, digital cameras and more than. (USB cable sold separately). Specifications General: Ability Source………………..................DC 5V ii.2A Adapter (Heart Positive) AC Power Supply……………………………………..100-240V ~ 50/60Hz 0.8A Grade 2 Bluetooth Ranges ………………………………………………33ft (10m) Supported Bluetooth Profile………………………………………………….A2DP Bombardment Backup……………………………………..two x 1.5V "AAA" size batteries Speaker………………………………………………………………….1 ten 4 ohms Output Power.........................................................................................2W x 1 USB Jack DC Power Output……………………………………………..…5V 2A Radio section: Frequency Range (FM)………………………….………………..87.five—108 MHz Specifications are subject to change without discover. For further assistance, please visit our website at hellocapello.com or contact customer service at support@capelloproducts.com or 1-855-896-1795 Life Lab International Ltd. The Bluetooth ® word marker and logos are registered trademarks endemic by Bluetooth SIG, Inc. and any use of such marks by Life Lab International LTD. is nether license. Other trademarks and trade names are those of their respective owners.
Capello Alarm Clock How To Set Time,
Source: https://fccid.io/AUICR60/User-Manual/User-Manual-3324749
Posted by: scottgooked.blogspot.com
0 Response to "Capello Alarm Clock How To Set Time"
Post a Comment